配置和用途：
1.立式机械手适用于50~180吨的各型立式射出成型机,用于取出成品及水口.
2.型号有LPL-V550/LPL-V650,手臂形式有单截式;上下行程从550~650mm,专用于两板模具.
3.机械手可以提高产能,降低产品的不良率和精准的控制生产量.
4.保障操作人员的安全性,减少浪费.
2.型号有LPL-V550/LPL-V650,手臂形式有单截式;上下行程从550~650mm,专用于两板模具.
3.机械手可以提高产能,降低产品的不良率和精准的控制生产量.
4.保障操作人员的安全性,减少浪费.
结构和功能：
1.左右旋转结构,方便调整置物方向,不需更换气管及磁簧开关.
2.夹具旋转机构,可以旋转180°放置成品及水口.全机可旋转45°,90°.
3.上下手臂采用进口的高钢性线性滑轨,引拔采用质量轻高钢性铝合金挤型梁配合线性轴承及高钢性轴承钢,可达到取出速度快,高效能,高精度,使用寿命长的要求.
1.左右旋转结构,方便调整置物方向,不需更换气管及磁簧开关.
2.夹具旋转机构,可以旋转180°放置成品及水口.全机可旋转45°,90°.
3.上下手臂采用进口的高钢性线性滑轨,引拔采用质量轻高钢性铝合金挤型梁配合线性轴承及高钢性轴承钢,可达到取出速度快,高效能,高精度,使用寿命长的要求.
人性化设计：
1.控制系统采用对话式操作,可以切换中英文页面,操作简单和容易学习.
2.8组内建标准程式,可储存12组教导程式,完全满足生产各种产品的需求及形式.
3.50组模具记忆功能,可以节省换模后的设定调整.
4.自动侦测故障并记录,方便故障排除.
5.手动操作时,可显示所有输入,输出接点于操作界面上,维修方便快速.
6.LED显示重要信号,如安全门,开模完,允许关模,允许托进和成品检测.
7.备用输出点可以连接其它的自动化设备,如输送带和承接台等.
8.自动运转下可修改各项动作的延迟时间与记数,操作简单方便.
9.可以选购CE机型,符合EUROMAP与SPI的标准.
1.控制系统采用对话式操作,可以切换中英文页面,操作简单和容易学习.
2.8组内建标准程式,可储存12组教导程式,完全满足生产各种产品的需求及形式.
3.50组模具记忆功能,可以节省换模后的设定调整.
4.自动侦测故障并记录,方便故障排除.
5.手动操作时,可显示所有输入,输出接点于操作界面上,维修方便快速.
6.LED显示重要信号,如安全门,开模完,允许关模,允许托进和成品检测.
7.备用输出点可以连接其它的自动化设备,如输送带和承接台等.
8.自动运转下可修改各项动作的延迟时间与记数,操作简单方便.
9.可以选购CE机型,符合EUROMAP与SPI的标准.
Configuration and use
1.V series used in 50 ~ 180 tons of various types of vertical injection molding machine, used to remove the product and the outlet.
2. Models have V550/650, arm in the form of single-cut type; vertical stroke from 550 ~ 650mm, dedicated to the two plate mold.
3. Manipulator can increase productivity, reduce product defect rate and precise control of production.
4. To protect the safety of the operator, to reduce waste.
1.V series used in 50 ~ 180 tons of various types of vertical injection molding machine, used to remove the product and the outlet.
2. Models have V550/650, arm in the form of single-cut type; vertical stroke from 550 ~ 650mm, dedicated to the two plate mold.
3. Manipulator can increase productivity, reduce product defect rate and precise control of production.
4. To protect the safety of the operator, to reduce waste.
1. About rotating structure, facilitate the adjustment of the direction glove compartment, no need to replace pipe and reed switches.
2. Fixture rotating body can be rotated 180 ° to place product and outlet. Entire machine can rotate 45 °, 90 °.
3. The upper and lower arm ofimport ed high-rigidity linear guide, lead to pull out with light weight high rigidity aluminum alloy extrusion with linear bearings and high-beam steel bearing steel, can reach out speed, high-performance, high-precision long service life requirements
2. Fixture rotating body can be rotated 180 ° to place product and outlet. Entire machine can rotate 45 °, 90 °.
3. The upper and lower arm of
1. Control system uses interactive operation, you can switch pages in English, simple and easy to learn.
2.8 set the standard built-in programs, can store 12 groups to teach the program, fully meet the production needs of a variety of products and forms.
3.50 Section mold memory function, can save the settings after the adjustment for mold.
4. Automatically detect the failure and records to facilitate troubleshooting.
5. Manual operation, it can display all input and output contacts on the user interface, the service quickly and easily.
6.LED displayimport ant signal, such as security doors, molding finished, allow off-mode, allowing prop forward and finished product testing.
7. Spare output point can be connected to other automation equipment, such as conveyor and receiving station.
8. Automatic operation can be modified under the action of the delay time and counting, simple operation.
9. Can buy CE model, consistent with EUROMAP and SPI standards.
2.8 set the standard built-in programs, can store 12 groups to teach the program, fully meet the production needs of a variety of products and forms.
3.50 Section mold memory function, can save the settings after the adjustment for mold.
4. Automatically detect the failure and records to facilitate troubleshooting.
5. Manual operation, it can display all input and output contacts on the user interface, the service quickly and easily.
6.LED display
7. Spare output point can be connected to other automation equipment, such as conveyor and receiving station.
8. Automatic operation can be modified under the action of the delay time and counting, simple operation.
9. Can buy CE model, consistent with EUROMAP and SPI standards.
